DISPENSERS / APPLICATORS
KEY
Tube
Cartridge
1-kg Can
Pail
Bottle
Syringe
Air Dispenser
COATER S4
Standard valve controller for controlling application. MODE settings and counter display are shown on an easier-to-see liquid crystal display. New preset functions have been added with count down ability along with conventional count up. Automatic reset and external output ability after setting count up or down.
| Outer Dimensions | W109×H217.5×D210.5 mm |
| Weight | Approx. 2.4 kg |
| Drive Sources | Clean dry air, 0 to 0.7 MPa, 100 to 240 VAC, 50/60 Hz |
| Suitable Materials | Compatible with low to high viscosity liquids. *Varies by dispensing parts. |
Air Dispenser
MINI COATER C5
Combining an air pressure controller with a syringe and syringe adapter is the most basic setup for single-component discharge equipment. Compatible with liquids with viscosity from low to high, including epoxy, silicone, UV resins, solder paste, silver paste, grease, oil, and a variety of other adhesives providing a wide range of use.
| Outer Dimensions | W190×D136×H72.5 mm |
| Weight | 1.7 kg |
| Drive Sources | Clean dry air, 0 to 0.7 MPa, 100 to 240 VAC, 50/60 Hz |
| Suitable Materials | Compatible with low to high viscosity liquids, *Varies by liquid product combination. |
AIR GUN FOR CARTRIDGE / AIR GUN FOR TUBE
DH1-C/ DH1-T
Specific needle nozzles can be attached to a cartridge or tube attachment in conjunction with the nozzle block.
| Outer Dimensions | W265×D70×H175 mm |
| Weight | 720 g |
| Drive Sources | Clean dry air, 0 to 0.4 MPa |
| Suitable Materials | For cartridge: Cartridge container For tube: 100-g/150-g tube moisture-curing sealant and adhesive, etc. |
TRANSFER-TYPE SIMPLE APPLICATOR
COATER R
Coater R is a unit that simplifies application of sealant to threaded areas of the bolts and fittings needed in piping and assembly processes. Small and easy-to-carry for application work in a variety of locations.
| Outer Dimensions | W150.5×D70×H90 mm |
| Weight | 870 g |
| Drive Sources | 100 VAC, 50/60 Hz |
| Suitable Materials | Anaerobic sealing adhesive |
ROTARY APPLICATOR
RTM2
Equipment that applies anaerobic sealing adhesive to the inner surface of cylindrical parts. Integration in processing and assembly lines improves productivity.
| Type | RTM2 application head | Dispense Valve | Metal pressure feed tank (PV2 tank) | Remaining amount detection sensor |
| Outer dimensions | W32×D313.6×H98 mm Not including bulb bracket |
- | W252×D315×H516 mm Standard Specifications |
- |
| Weight | 0.93kg | - | Approx. 6.7kg | |
| Drive Sources | Electricity of 24 VDC 5 A or more (120 W or more) is recommended | *For valve Clean dry air, 0.3 MPa or more | - | - |
| Suitable Materials | Anaerobic sealing adhesive | |||
MANUAL ROTARY APPLICATOR
RTA-H
Anaerobic sealing adhesive drips into the rotor in the air gun tip, which rotates to apply the anaerobic sealing adhesive to the inner surface of cylindrical objects.
| Type | Air Gun | Controller | Material pressure feed tank (PV2 tank) |
| Outer Dimensions | W210×D57×H210 mm | W250×D190×H250 mm | W252×D315×H516 mm Standard Specifications |
| Weight | 1.5 kg | 2 kg | 6.7 kg |
| Drive Sources | Clean dry air, 0.3 MPa or more, 100 VAC or 200 VAC, 24 VDC |
Clean dry air, 0 to 0.2 MPa, Remaining amount detection sensor, 10 to 36 VDC | |
| Suitable Materials | Anaerobic sealing adhesive, other | ||
MANUAL DISPENSER FOR
LOW VISCOSITY LIQUIDS
TANK FOR 250G/1 KG BOTTLE OR CAN
(PT-005/PT-01)
PEN TYPE MANUALLY OPERATED VALVE
(PENCIL GUN)
This dispenser enables hand-operated pencil gun application of low viscosity liquids via a pressure tank. Coating is easily adjusted via air pressure of the pressure tank and opening or closing the pencil gun lever.
| Type | Tank PT-005 | Tank PT-01 | Pencil Gun | |
| Outer Dimensions | W149×D149×H226 mm | W162×D162×H247 mm | Ø12×152 mm | |
| Weight | 2 kg | 3.6 kg | 100 g | |
| Drive Sources | Clean dry air, 0 to 0.5 MPa | |||
| Suitable Materials | Liquid gasket, moisture-curing sealant and adhesive, single-component epoxy resin, UV-curing resin | |||
DISPENSER FOR TUBE-PACKAGED MATERIALS
TUBE DISPSENSE TANK AIR DISPENSER (MINICOATER C5)
Basic air pressure controlled dispenser optimal for tube-packaged material application. This simple dispenser controls air with mini coater C5 to handle a wide range of materials.
| Type | Tank for 100-g tube | Tank for 150-g tube |
| Outer Dimensions | Ø450×200 mm | Ø450×210 mm |
| Weight | 334 g | 466 g |
| Drive Sources | Clean dry air, 0 to 0.7 MPa, 100 to 240 VAC, 50/60 Hz | |
| Suitable Materials | For tube: 100-g/150-g tube moisture-curing sealant and adhesive, etc. | |
INSTANT ADHESIVE DISPENSER
TANK WITH REMAINING AMOUNT SENSOR DETECTION (PT-01E) MICRO DISPENSE VALVE (TDV) EXCLUSIVE CONTROLLER
Dispenser for applying difficult-to-handle instant adhesive via a diaphragm valve.
| Outer Dimensions | W160×D40×H90 mm |
| Weight | 650 g |
| Drive Sources | Clean dry air, 0.3 to 0.5 MPa |
| Suitable Materials | Instant Adhesives |
SINGLE-COMPONENT FIXED-QUANTITY BOOSTER SERIES
SCB SERIES SCB-28-CL/SCB-17-LE/DQ1LW06
Discharges a fixed volume by consistent velocity drive of the plunger via a stepping motor. Discharge speed is controllable via numerical values to simplify adjustments in application.
| SCB-28-CL | SCB-17-LE | DQ1LW06 | ||||
| Type | Clutch Type | Controller | Base Model | Controller | Lightweight Type | Controller |
| Outer Dimensions | W178×D135×H417 mm | W320×D280×H180 mm | W150.5×D108.5×H374 mm | W320×D350×H226 mm | W125.5×D133×H440 mm | W320×D300×H160 mm |
| Weight | 6 kg | 10 kg | 3 kg | 10 kg | 6 kg | 10 kg |
| Drive Sources | 100 VAC or 200 VAC±10%, 50/60 Hz | 24 VDC, 50/60 Hz | 100 to 240 VAC±10%, 50/60 Hz | |||
| Suitable Materials | Moisture curing sealants and adhesives | |||||
INSTANT ADHESIVE DISPENSER
TUBING PUMP TF300MP-S
Tubing pump discharge prevents runs, leaks, and clogs while ensuring liquids are used completely. Adhesive only passes through the material tube, so it can be left to sit for several days without curing and the device can be operated quickly.
| Outer Dimensions | W210×D200×H87 mm |
| Weight | 3.5 kg |
| Drive Sources | 100 VAC, 50/60 Hz |
| Suitable Materials | Instant Adhesives |
PRESSURE FEED TANK
PT-005 / PT-01 / PT-03
The material pressure feed tank is for pressure feeding medium and low-viscosity materials. Uses compressed air to feed material from the container set in the tank.
| Type | PT-005 | PT-01 | PT-03 |
| Outer Dimensions | W149×D149×H226 mm | W162×D162×H247 mm | W300×D300×H415 mm |
| Weight | 2 kg | 3.6 kg | 21 kg |
| Drive Sources | Clean dry air, 0 to 0.5 MPa | Clean dry air, 0 to 0.77 MPa | |
| Suitable Materials | Liquid gasket, moisture-curing sealant and adhesive, anaerobic sealing adhesive, volatile solvent-type adhesive, instant adhesive, single-component epoxy resin, UV-curing resin | ||
Pumps
KEY
Tube
Cartridge
1-kg Can
Pail
Bottle
Syringe
SINGLE-ACTING PUMP FOR PAILS: PBIII SERIES
PBIII-30/45
Pump for high-pressure feeding of high-viscosity materials from pails. Uniform linear application is possible when combined with a robot.
| Type | PBIII-30 | PBIII-45 |
| Outer Dimensions | W430×D500×H1031.4 to 1458.4 mm | W430×D500×H1050.4 to 1477.4mm |
| Weight | Approx. 120 kg | |
| Drive Sources | Clean dry air, 0.3 to 0.6 MPa | |
| Suitable Material Viscosity | Moisture-curing sealant and adhesive, single-component epoxy resin | |
MANUAL APPLICATION CARTRIDGE PUMP
ACB-20 *Pen type manually operated valve (pencil gun)
Unit for high-pressure feeding of high-viscosity materials from cartridge containers. Suggested for manual application. Automatic refill of the pump when it reaches the bottom of its stroke.
| Outer Dimensions | W320×D255×H630 mm |
| Weight | 16 kg |
| Drive Sources | Clean dry air, 0.4 to 0.6 MPa, Power source, 100 VAC |
| Suitable Material Viscosity | Moisture curing sealants and adhesives |
SINGLE-ACTING PUMP FOR PAILS: PB SERIES
PB-30/45/60
Equipment for high-pressure feeding of high-viscosity sealant. Uniform linear application is possible when combined with a robot and dispense valve with no pulsation.
| Type | PB30 | PB45 | PB60 |
| Outer Dimensions | W370×D670×H1105 to 1503 mm | W420×D670×H1170 to 1565 mm | W500×D672×H1472 to 1863 mm |
| Weight | 2 Approx. 70 kg | Approx. 90 kg | Approx. 100 kg |
| Drive Sources | Primary clean dry air, 0.3 to 0.6 MPa Secondary clean dry air, 0.15 to 0.4 MPa |
Primary clean dry air, 0.4 to 0.6 MPa Secondary clean dry air, 0.2 to 0.4 MPa |
|
| Suitable Material Viscosity | Moisture-curing sealant and adhesive, single-component epoxy resin | ||
HIGH-VISCOSITY MATERIAL COMPATIBLE
CARTRIDGE PUMP
PCB-20
Unit for high-pressure feeding of high-viscosity materials from cartridge containers to secondary discharge valves. Uniform linear application is possible when placing the dispense valve onto a robot.
| Outer Dimensions | W335×D255×H645 mm |
| Weight | 18 kg |
| Drive Sources | Clean dry air, 0.2 to 0.7 MPa, 24 VDC (when using the auto switch) |
| Suitable Material Viscosity | Moisture curing sealants and adhesives |
DOUBLE-ACTING PUMP FOR PAILS (AP-30)
HIGH-PRESSURE FLOW GUN (H-FLG)
AP-30/45
This dispenser is excellent in high-speed dispense and functionality due to the combination of high-pressure feeding pump for pails with a high-pressure flow gun.
| Type | Pail pump | High-pressure flow gun |
| Outer Dimensions | W370×D671×H1028 to 1426 mm | - |
| Weight | 70 kg | 580 g |
| Drive Sources | Clean dry air, 0.3 to 0.6 MPa | |
| Suitable Material Viscosity | Moisture-curing sealant and adhesive, single-component epoxy resin | |
PUMP FOR 1-KG CANS
PH1-20
Pump for high-pressure feeding of materials loaded in 1kg metal cans. Use a can opener to open 1kg material package and set it into the pump without requiring pouring of liquid.
| Outer Dimensions | W300×D200×H555 to 710 mm |
| Weight | 26 kg |
| Drive Sources | Clean dry air, 0.2 to 0.6 MPa |
| Suitable Material Viscosity | Materials for heat dissipation with viscosities around 30 to 200 Pa•s, materials containing large amounts of fillers, materials other than those reactive to metal ions |
MATERIAL REDUCTION UNIT FOR LOW VISCOSITY FIPG
PUMP ACCESSORY
Material Reduction Unit for low viscosity FIPG that can be attached to conventional PB or PBIII pump.
Valves
KEY
Tube
Cartridge
1-kg Can
Pail
Bottle
Syringe
DISPENSE VALVE
HPNV-50
Needle type dispense valve well-suited to automatic application with excellent durability and pressure resistance. Optimal for use as a silicone-based material dispense valve. Running cost is reduced through simple attachment and removal of the material chamber.
| Type | HPNV-50 |
| Outer Dimensions | W40×D41.5×H150 mm |
| Weight | 470 g |
| Drive Sources | Clean dry air, 0.3 to 0.6 MPa |
| Suitable Material Viscosity | Liquid gasket, moisture-curing sealant and adhesive, single-component epoxy resin |
DISPENSE VALVE
SLENDER-SVR
Needle type pneumatic dispense valve that is compact and resistant to high-pressure. More accurate stopping point when dispensing than HPNV-50.
| Outer Dimensions | W28×D28×H166 to 170 mm |
| Weight | 430 g |
| Drive Sources | Clean dry air, 0.3 to 0.6 MPa |
| Suitable Material Viscosity | Liquid gasket, moisture-curing sealant and adhesive, single-component epoxy resin |
SURFACE APPLICATION ADHESIVE DISPENSE VALVE
SURFACE APPLICATION ADHESIVE DISPENSE VALVE PV-SN SERIES
This is a dispense valve for application of sealant and adhesive in coating form.
| Type | RV05-SN50 | RV10-SN100 | RV15-SN150 |
| Outer Dimensions | W161×D86.5×H124 mm to 1503 mm | W211×D86.5×H124 mm to 1565 mm | W261×D86.5×H124 mm to 1863 mm |
| Weight | 2.4 kg | 2.6 kg | 2.9 kg |
| Drive Sources | Clean dry air, 0.3 to 0.6 MPa | ||
| Suitable Material Viscosity | Moisture-curing sealant and adhesive, single-component epoxy resin, UV-curing resin | ||
FIXED-QUANTITY DISPENSE VALVE FOR ANAEROBIC
SEALING ADHESIVE
CVA3 / 4 /5
Pneumatic valve for dispensing fixed quantities of anaerobic sealing adhesive. Also compatible with some light curing resin.
| Type | CVA3 | CVA4 | CVA5 |
| Outer Dimensions | W50.5×D50.5×H218 mm | W30×D30×H176 mm | W30×D35×H201 mm |
| Weight | 540 g | 340 g | 350 g |
| Drive Sources | Clean dry air, 0.3 to 0.4 MPa | Clean dry air, 0.35 to 0.5 MPa | |
| Suitable Material Viscosity | Anaerobic sealing adhesive, other | ||
MICRO DISPENSE VALVE (TDV)
TDV VALVE
Valve for dispensing ThreeBond 1700 and 7700 series instant adhesive.
| Outer Dimensions | W160×D40×H90 mm |
| Weight | 650 g |
| Drive Sources | Clean dry air, 0.3 to 0.5 MPa |
| Suitable Material Viscosity | Instant Adhesives |
ANAEROBIC ADHESIVE AND SEALANT DISPENSE VALVE
KOBO VALVE
Valve for high accuracy discharge of anaerobic sealing adhesive in μL units. Optimal for extremely small quantity discharge from 30 to 200 μL.
| Outer Dimensions | W94×D40×H73.5 mm |
| Weight | 470 g |
| Drive Sources | Clean dry air, 0.3 to 0.5 MPa |
| Suitable Material Viscosity | Anaerobic sealing adhesive, other |
Other
KEY
Tube
Cartridge
1-kg Can
Pail
Bottle
Syringe
FIXED QUANTITY DISPENSER
DQ1EP
Dispenser where the single-component fixed-quantity booster (see above) drive has been converted to electric. Maximum discharge in a single cycle is 28cc.
| Outer Dimensions | W160×D110×H400 mm |
| Weight | 9 kg |
| Drive Sources | 3-phase 200 V |
| Suitable Material Viscosity | Moisture curing sealants and adhesives |
PUMP FOR CARTRIDGES
PC1-11EP
Equipment where the cartridge pump (see above) drive has been converted to electric. Electric automatic cartridge tank switching is standard.
| Outer Dimensions | W580×D610×H1600 mm |
| Weight | 200 kg |
| Drive Sources | 3-phase 200 V |
| Suitable Material Viscosity | Moisture curing sealants and adhesives |
PUMP FOR PAILS
PP1-10EP
Equipment where the pail pump (see above) drive has been converted to electric. A servo motor controls the raising/lowering of the pump enabling the FIPG remaining amount detection to be set.
| Outer Dimensions | W600×D860×H1870 mm |
| Weight | 340 kg |
| Drive Sources | 3-phase 200 V |
| Suitable Material Viscosity | Moisture curing sealants and adhesives |
CONTROLLER
Controls an electric FIPG application system with a single controller.
| Type | Controller | Operation part |
| Outer Dimensions | W850×D250×H1200 mm | W250×D120×H250 mm |
| Weight | 110 kg | 5 kg |
| Drive Sources | 3-phase 200 V | |
DESKTOP ROBOT
RT7 SERIES
This new style desktop robot has a low price without sacrificing practicality and provides an incredible cost performance. The stepping motor combined with a special micro-step drive circuit saves on energy and space.
| Type | RT7-20 | RT7-30 | RT7-40 | RT7-50 |
| Operation Range | X200×Y200×Z50 mm | X300×Y320×Z100 mm | X400×Y400×Z150 mm | X510×Y510×Z150 mm |
| Maximum Payload | Workpiece, 7.0 kg / tool, 3.5 kg | Workpiece, 15.0 kg / tool, 7.0 kg | Workpiece, 15.0 kg / tool, 7.0 kg | Workpiece, 15.0 kg / tool, 7.0 kg |
| Outer Dimensions | W323×D387×H554 mm | W560×D535×H659 mm | W584×D631×H807 mm | W678×D731×H807 mm |
| Weight | 20 kg | 35 kg | 42 kg | 44 kg |
AUTOMATIC APPLICATION DEVICE FOR
LOW AND MEDIUM VISCOSITY MATERIALS
EQUIPMENT LIST
Tank for 250-g/1-kg bottle or can (PT-005/PT-01) Dispense valve (HPNV-50) Pressure feed controller (coater S4) Desktop 3-axis robot (RT7-20)
| Drive Sources | Clean dry air, 0 to 0.7 MPa, 100 to 240 VAC, 50/60 Hz |
| Suitable Viscosity | Low and medium viscosity materials |
| Suitable Materials | TB1100 series, liquid gasket TB2000, 2100, 2200 series epoxy resin adhesives TB3000, 3100 series UV curing resin |
| Suitable Packaging | 250-g bottles, 1-kg bottles or cans |
AUTOMATIC APPLICATION DEVICE FOR
LOW AND MEDIUM VISCOSITY MATERIALS
EQUIPMENT LIST
333-ml cartridge-type tank Liquid agent discharge valve (HPNV-50) Pressure feed controller (coater S4) Desktop orthogonal 3-axis robot (RT7-20)
| Drive Sources | Clean dry air, 0 to 0.7 MPa, 100 to 240 VAC, 50/60 Hz |
| Suitable Viscosity | Low and medium viscosity liquid agents |
| Suitable Materials | Moisture curing sealant such as TB1200 and TB1500 series UV curing resin such as TB3000 and 3100 series |
| Suitable Packaging | 333-ml cartridge |
FIXED-QUANTITY APPLICATION DEVICE FOR
HIGH-VISCOSITY MATERIALS
EQUIPMENT LIST
Pump for pails (PBIII) Constant-velocity discharge head (fixed-quantity booster) Desktop 3-axis robot (RT7-30)
| Drive Sources | Clean dry air, 0.3 MPa or more, 100 VAC, 24 VDC |
| Suitable Viscosity | Low to high viscosity |
| Suitable Materials | Moisture curing sealant such as TB1200 and TB1500 series |
| Suitable Packaging | Pail |
Accessories
KEY
Tube
Cartridge
1-kg Can
Pail
Bottle
Syringe
Nozzle
STAINLESS STEEL NEEDLE / PTFE NEEDLE NOZZLE / PRECISION NOZZLE
Nozzles made of various materials (including metal) are available in many sizes. You should select a nozzle material suitable for the properties of the dispense material used.
NOZZLE BLOCK
NB2 / NB2R / NB4 / NB5
Connects the valve with the nozzle. We can manufacture an integral type of nozzle block combined with your specified nozzle diameter/ length to fit a custom application.
CARTRIDGE ACCESSORIES
CARTRIDGE TANK ALUMINUM TANK WITH CYLINDER CARTRIDGE ATTACHMENT LOW-VISCOSITY, LOW-THIXOTROPY MATERIAL COMPATIBLE CARTRIDGE TANK (LVCT-AC)
Pressure feed tank used to pressure feed cartridge-type sealants and adhesives.
SYRINGES AND SYRINGE ACCESSORIES
SYRINGE / ADAPTER / ADAPTER ASSEMBLY
Syringes and related accessories used for manual application of micro and low volumes.
TUBES AND HOSES
PTFE TUBES / NYLON TUBES / HIGH AND LOW PRESSURE PTFE HOSES
Our lineup of products provides a variety of options.
HAND GUN FOR TWO-COMPONENT LIQUID CARTRIDGE
TB2086M / TB3955 DEDICATED USE HAND GUN
Hand gun that dispenses by mixing material within a static mixer.
